COMMERCIAL TANDEM BUSHING BEARING PUMPS
K37
WITH ONE PIECE SHAFT & GEARS
2 BOLT TYPE A
|
2 BOLT TYPE B
|
2 BOLT TYPE C
|
4 BOLT TYPE B
|
4 BOLT TYPE C
3-1/4” Round Pilot
|
4” Round Pilot
|
5” Round Pilot
|
4” Round Pilot
|
5” Round Pilot
4-3/16” Bolt Circle
|
5-3/4” Bolt Circle
|
7-1/8” Bolt Circle
|
5” Bolt Circle
|
6-3/8” Bolt Circle
TO CHANGE ROTATION on P300 series double pumps rotate the gear housing 180
o
& rotate all of the thrust plates 180
o
being careful not to lose the
channel seals on the backside of them. Also rotate the bearing carrier 180
o
and rotate the rear cover 180
o.
Pump With
|
Gallons Output & Horsepower Required at 1500 PSI
Splined Shaft
Max. |
Shaft End Pump
|
Cover End Pump
and Flange
Pres- |
1200 RPM
|
1800 RPM
|
2400 RPM
|
1200 RPM
|
1800 RPM
|
2400 RPM
Mount
sure |
GPM
HP |
GPM
HP |
GPM
HP |
GPM
HP |
GPM
HP |
GPM
HP
Number
PSI |
OutPut
InPut | OutPut
InPut | OutPut
InPut | OutPut
InPut | OutPut
InPut | OutPut
InPut
P330B497FJAB10-25KMAB07-1
3500 |
8.5
9.9 | 14.0
16.3 | 19.0
22.2 | 7.0
8.2 | 10.7
12.5 | 17.0
19.8
P330B497FJAB12-25KMAB10-1
3500 |
11.5
13.4 | 18.0
21.0 | 24.0
28.0 | 8.5
9.9 | 14.0
16.3 | 19.0
22.2
P330B497FJAB15-25KMAB12-1
3500 |
14.0
16.3 | 21.5
25.1 | 29.0
33.8 | 11.5
13.4 | 18.0
21.0 | 24.0
28.0
P330B497FJAB17-25KMAB15-1
3250 |
16.0
18.7 | 25.0
29.2 | 34.0
39.7 | 14.0
16.3 | 21.5
25.1 | 29.0
33.8
P330B497FJAB20-25KMAB17-1
3000 |
18.5
21.6 | 29.0
33.8 | 39.0
45.5 | 16.0
18.7 | 25.0
29.2 | 34.0
39.7
P350B442FBAB10-7KBAB07-1
3500 |
11.5
13.4 | 17.5
20.4 | 24.5
28.6 | 9.0
10.5 | 13.7
16.0 | 18.5
21.6
P350B442FBAB12-7KBAB10-1
3500 |
15.0
17.5 | 23.0
26.8 | 31.0
36.2 | 11.5
13.4 | 17.5
26.8 | 24.5
28.6
P350B442FBAB15-7KBAB12-1
3500 |
18.0
21.0 | 27.5
32.1 | 37.0
43.2 | 15.0
17.5 | 23.0
32.1 | 31.0
36.2
P350B442FBAB17-7KBAB15-1
3250 |
21.0
24.5 | 32.5
37.9 | 44.0
51.3 | 18.0
21.0 | 27.5
32.1 | 37.0
43.2
P350B442FBAB20-7KBAB17-1
3000 |
24.0
28.0 | 37.5
43.8 | 51.0
59.5 | 21.0
24.5 | 32.5
37.9 | 44.0
51.3
P350B442FBAB22-7KBAB20-1
2750 |
27.0
31.5 | 42.0
49.0 | 57.0
66.5 | 24.0
28.0 | 37.5
43.8 | 51.0
59.5
P350B442FBAB25-7KBAB22-1
2500 |
30.0
35.0 | 47.0
54.8 | 63.5
76.1 | 27.0
31.5 | 42.0
49.0 | 57.0
66.5
P365B478FBAB10-7KBAB07-1
3500 |
15.5
18.1 | 24.5
28.6 | 34.0
39.7 | 12.2
14.2 | 19.0
22.2 | 26.7
31.2
P365B478FBAB12-7KBAB10-1
3500 |
20.0
23.3 | 31.5
36.8 | 43.0
50.2 | 15.5
18.1 | 24.5
28.6 | 34.0
39.7
P365B478FBAB15-7KBAB12-1
3500 |
24.5
28.6 | 38.0
44.3 | 52.5
61.3 | 20.0
23.3 | 31.5
36.8 | 43.0
50.2
P365B478FBAB17-7KBAB15-1
3500 |
29.0
33.8 | 45.5
53.1 | 62.0
72.4 | 24.5
28.6 | 38.0
49.3 | 52.5
61.3
P365B478FBAB20-7KBAB17-1
3500 |
33.5
39.1 | 52.0
60.7 | 71.0
82.9 | 29.0
33.8 | 45.5
53.1 | 62.0
72.4
P365B478FBAB22-7KBAB20-1
2500 |
38.0
44.3 | 59.0
68.8 | 80.5
93.9 | 33.5
39.1 | 52.0
60.7 | 71.0
82.9
P365B478FBAB25-7KBAB22-1
3000 |
43.0
50.2 | 66.0
77.0 | 90.0 100.5 | 38.0
44.3 | 59.0
68.8 | 80.5
93.9
Prices subject to change without notice
Pumps in this series are positive displacement type used to produce a
flow of hydraulic fluid. Flow rate depends on the pump size, the speed at
which it is driven and the resistance or pressure it is pumping against.
Pump ratings in GPM at 1200 RPM and at 2000 PSI. For ratings at
other speeds refer to the application chart below
Rotation is right hand clockwise facing shaft end.
We stock Pumps, Repair Parts, Seal Kits, Shafts, Bearings & Foot Mounts
FOR ALL UNITS
To determine direction of shaft rotation, view the unit with the shaft
pointing toward you, and the idler (driven) gear beneath the shaft. With
clockwise rotation, flow will be left to right. The inlet port will be on the
left, outlet on the right. The flow is in the opposite direction with counter-
clockwise rotation. Inverting the pump will reverse the inlet and outlet ports
but not the direction of rotation.
CUSTOM BUILT PUMPS BUILT FROM PARTS
ARE NON-RETURNABLE